3x3 DIY Uncaged Press Plates Kit - DIY 6 Ton Rosin Press Pairing It Well with 6-ton A-frame Press

Out of stock
Uncaged Press Plates
$289.00 $189.00
3x3 DIY Uncaged Press Plates Kit - DIY 6 Ton Rosin Press Pairing 6-ton A-frame Press for Home Use


  • 3x3" Size Heated Plates - Pairs well with a 3-6 ton A-frame hydraulic shop press to build your own press; 3x3 " platen well suited to squeeze 3.5-7g material.
  • Anodized Heated Platen - Anodized working surface is easy to clean up, and offers even heating.
  • Accurate Temp Detected - Durable dual heating PID temp controller; Accurate temp delivered utilizing separate thermocouple and heating rods.  
  • Long Working Life Guaranteed - The heating rods have a service life of more than 6,000 times.
  • Bottom Plate Holder Not Included - Please secure dual heated platens working in alignment; not including bottom plate holder for 3x3 kit.


    • Temperature Range: 0-399F 
    • Voltage: 110/220V
    • Power: 300W
    • Plate Size: 3" x 3"
    • Top Platen in Height: 2 3/8"
    • Bottom Platen in Height: 1 1/8"  
    • External Package: 14" x 14.2" x 6.1"
    • Gross Weight: 8.15lbs

      How to Avoid the Filter Bags from Blowing out?

      • Remove excess stems from flowers.
      • Use less material in your filter bag.
      • Preheating your material first to get it melty before you begin to apply pressure.
      • Apply the pressure more slowly.
      Manual & Troubleshooting Includes:

      • How to choose filters and prepress molds.
      • The yields are not very good, why?
      • How to install the DIY press plates kits
      • How to choose hydraulic press for pairing
      • How to apply the pressure for optimal yield and quality?
      • How to begin extracting.
      • Important notice.
      • Troubleshooting.
      • Question and answer.
      • Check it out here (Highly recommended to read it before doing a purchase).

          Customer Reviews

          Based on 10 reviews


          Started looking into this after my plug dried up. Was expecting pressing to be a whole thing I had to learn, and figure out how to do. Ended up on reddit and read about "Press Plates" and the rest was history! Initially was planning on a 3x5 since thats what I thought was the smallest unit....literally doing this just for me and a G of concentrate will usually last me an entire week or more....so this 3x3 unit is perfect for my uses!

          Im in a location thats not conducive to getting the most premium flowers.....so I would honestly call my good stuff mids in places like Cali. Well....pressed a few nugs as a tester to see what was up. Set the PID to 205.....used my harbor freight press to squish....let sit about 1 minute.....and I yielded 16% on my first try! Not bad for a first time on a harbor freight press, using mids....for a TOTAL NOOB! Squished some "GOOD stuff" and yielded 18% on my third try! Second one wasnt as good...but that was at different temps....its cool to see the PID really works giving the different results depending on temp!

          Cant wait to master this bad boy and yeild 20%+ on the regular! I wish I had the cage....but i was looking for the cheapest route. Ordered some heat resistant BBQ gloves, which I recommend....and that should basically solve the desire for wanting the cage. Plates dont really move....and it doesnt really matter imo if you take it slow when squishing....but itll give me peace of mind to hold it in place until the pressure hits. Get the cage model if budget is not an issue or time is at a premium.....but if youre budget minded like me, get the uncaged and save the money cuz its not really a big deal at all when pressing small/personal amounts. If I had to do it again....I would choose this same 3x3 model for myself.

          Works great

          In hawaii a shop press is hard to get shipped so i had to get dp-rp33 3x3 anodized plates because of my 6-ton H shop press. I am squishing nugs 10g at a time in 2.5x4.5 micron bags and the dp-pm40r puck maker. One day i hope i can get a 20-ton H press delivered to the island and the HUGE 5.5x7 cube.

          Works great so far and looks

          Great press kit

          Well build, easy to use, highly recommend

          Very happy with this purchase. Everything looks and feels very well built, first two uses were simple and hassle free. Perfect for personal production

          Prime Time!

          I cant tell you enough how well these plate work. Great price and they look great to. Its easy to use and adjusted PID. The company seems to be on top of it for shipping efficiently so all and all I would recommend this product to anyone looking for a good plate setup. Dont haste, press and taste!

          User Manual & Troubleshooting Includes:

          - Recommendations on Materials Loaded
          - How to Begin Extracting
          - How to Start
          - Installation
          - Important Notices
          - Questions & Answers
          - Troubleshooting

          User Manual List:

          1, Cylinder Pre Press Mold 
          2, 2X4" Pre Press Mold 
          3, DIY Uncaged Press Plates Kit 
          4, Bottle Jack Styled Rosin Press 
          5, DIY Caged Press Plates Kit 
          6, Hydraulic Cylinder Styled Rosin Press 
          7, Rosin Bags & Combo 
          8, Hydraulic Hand Pump with Gauge 


          Ask a Question
          • I bent one of the tightening bolts on the plate so now when i tighten it the plates don't stay square, can i replace the bolt? If so do you know the size?

            Please buy M8 screws, and replace the bent one. Have a nice day!

          • How much budd can I press at one time with these plates.

            We recommend 1.5-7g small batches at a time, it is great to be paired a cylinder pre press mold for high yield ( bottle tech style pre press mold ).

          Have Questions? Reach out Here
          You have successfully subscribed!