30mm SS Hammer Styled Pollen Press ( Flower & Hash ) - Works with 2x4" Filters, Loading 7g Materials
30mm SS Hammer Styled Pollen Press ( Flower & Hash ) - Works with 2x4" Filters, Loading 7g Materials
- Hash & Flower - The cylinder pre-press mold well suited to compress flower, and hash, etc.
- 0.15mm Gap - Small gap cylinder prepress mold also works great with kief, hash, and flower.
- Hammer Styled Mold - After loading material and insert the hammer nail, and strike it with a rubber mallet!
- PVC Sheet Included - Easy to insert pucks into filter bags with PVC sheet attached.
- Save Rosin Filter- Double squashes by cutting 2x4.5" rosin bags into half for flower if pairing it with cylinder mold.
- Item No.: dp-pm30h
- Material: 304 Stainless Steel
- Inner Diameter: 1.18 inch (30mm)
- Outer Diameter: 1.46"
- Height: 3.38"
How to Avoid Filter Bags from Blowing out?
- Remove excess stems from flowers.
- Use less material in your filter bag.
- Preheating your material first to get it melty before you begin to apply pressure.
- Apply the pressure more slowly.
- How to start
- Recommendations on materials loaded.
- Rosin filter bags suggested.
- The yields are not very good, why?
- How to apply the pressure for optimal yield and quality?
- How to begin extracting.
- Important notice.
- Troubleshooting.
- Question and answer.
- Check it out here (Highly recommended to read it before doing purchase)
PID TEMP CONTROLLER SETTING:
Press "SET" button to activate temperature controller
Press ◄ button to increase and decrease the value at hundreds, tens and one's places
Press ▼ or ▲ from 0-9 for your desired temp
Press "SET" button to lock the desired temperature in place
CHECK-UP BEFORE BUYING:
Everything before it was promised and in perfect condition. Most impressive shipping boxes I've ever seen. Very well built and user friendly. Only been using it for a week and already pressing out fine product to be proud of. Very easy to learn with as I've never done it before now.
parfait fait bien son travail
Hey guys and Gals
Great prepress works like an charm and bags never blow out great products
User Manual & Troubleshooting Includes:
- Recommendations on Materials Loaded
- How to Begin Extracting
- How to Start
- Installation
- Important Notices
- Questions & Answers
- Troubleshooting
User Manual List:
1, Cylinder Pre Press Mold
2, 2X4" Pre Press Mold
3, DIY Uncaged Press Plates Kit
4, Bottle Jack Styled Rosin Press
5, DIY Caged Press Plates Kit
6, Hydraulic Cylinder Styled Rosin Press
7, Rosin Bags & Combo
8, Hydraulic Hand Pump with Gauge
QUESTIONS & ANSWERS
Ask a Question-
Can I use a hammer or mallet to compress the pucks?
Yes! Please use a rubber mallet to prevent scratching your plunger.
-
Do I need to use filter bags for flowers?
No, you can press single flowers and get great results, you can also use the pre press molds to form pucks to press without the use of filters. Keep in mind when not using filters that the puck will expand a bit larger.
-
Can I re-press my pucks?
Yes! Simply fold the puck in half and re-press it. You might have to use higher temperature to get an extraction.
-
How to measure the humidity in my flower container?
A small hygrometer will give you the humidity levels inside of the container.
-
What Humidity level should my flower be stored in?
62% is the recommended stable relative humidity (RH) inside of your flower container.
-
Can I compress the pucks using my arbor press?
Yes, though be careful not to apply too much pressure onto the aluminum surface directly.
-
What is the recommended minimum amounts loaded?
For the 30mm molds, 3.5g, for the 40mm mold, 7g.
