My Temp Controller Box Caused the Issue After Changing the Parameters, How to Fix It? First of all, we do not recommend changing the internal parameters, which will cause a lot of problems. Once a problem occurs after the modification, please refer to the following instructions to change back to the default. How to Change back to the Default Setting of TC01V5? #The following instruction is only applicable to "TC01V5" PID controller, not for "TC20V2". As of May 1st,2021, Only Dabpress 12 ton heat press uses a PID temp controller with Item number "TC20V2". # First of all, please refer to the...
How to Replace PID module? 1. Unplug the power cord from the rear of the temperature control box.2. Turn the temperature control box upside down to access the locking mechanism on the front of the PID module housing face.3. Use a dab tool or small flat head screwdriver to depress in on the locking mechanism at the front of the PID housing face.4. While depressing the locking mechanism, simply slide out the front of the box, the PID module from the housing (there will be 2 circuit boards exposed).5. Install the replacement PID module received (remove it from the included...
About 2x4" Rosin Pre Press Mold, Why Is the inside of the Mold Not 2x4"? This is one of the most asked questions by rosineer, we named this mold 2x4 just to declare that it pairs with 2x4 rosin filter bags. In order to reduce your confusion, we specifically mention the size of puck in the description. Now Let Us Talk about It in Details as Below; Usually we need to use the mold to form pucks. Please understand that the compressed puck which you put into the filter bags is a three-dimensional block, it has length,width, height. The filter bag just has...
How to Replace the Bottle Jack?The instruction is applicable to bottle jack styled heat press machine that need to replace the jack step by step: 1. Loose the bolts under the base and on the collar if includes.2. Ask someone to help you lift up the the heated plates.3. Remove the bottle jack. 4. After loading the replacement. If the replacement offers a thread, please pre-install the screws and nuts (do not tighted it)5. Lift the bottle jack till dual heated platens touched, and then adjust the dual heating plates to align with each other.6. Lift up the bottom heated plate harder, tighten all...
Piston Rod of Hydraulic Cylinder Rosin Press Can Lift But It Can Not Move Back, What happened? Caution: 1. Please ensure the pump has a NPT 1/4” male fitting;2. We recommend you to replace male fitting (From another brand) with ours for matching our press. There is improper operation caused this kind of issue, please check it out carefully: 1. Please make sure the male and female coupler installed completely. You need to push the male fitting into the female one fully, at the same time, please tighten the nut of the female coupler. Please try to reconnect couplers once you didn’t...
My Rosin Press Hydraulic Hand Pump Will Not Maintain Pressure Well, Why? To help prevent personal injury, always release pump pressure and disconnect hoses(s) from pump before making repairs.Refer to the appropriate pump parts list during trouble-shooting. Please check these problems yourself first, and then make clear what happened to your pump: Problem Cause Solution Pump losing pressure System components leaking Directional control valve leaks ornot adjusted properly Fluid leaking past outlet checkseat(s) Repair or replace as necessary Reseat, repair, or replace directional control assembly and correctly adjust Check for dirt. Reseat pump body and/or replace poppet(s) or ball(s) Pump not delivering...
Rosin Press Delivered the Inaccurate Temperature After Measuring with My Infrared (IR) Thermometer Gun, Why? To be honest, when we measure the temperature of the heating plate during the process of manufacturing, the temperature obtained by the infrared thermometer is different every time. Actually, many factors will affect the test results: 1. Measure different positions of the heating plate. 2. Measure under different ambient temperature. 3. Measure after modifying the parameters. 4. Measure by the different brands.5. Measure at different time points in the heating process. If possible, we recommend that you use a contact thermometer to measure the temperature or please verify the...
Why Can't We Use Rosin Press to Produce the Puck of Flower or Hash? We at Ddabpress Team often receive complaints from Rosineers about why 2x4" rosin pre press mold can not load between the heated plates of the rosin press for making puck. Honestly, we can only patiently explain to customers that this kind of operation will scratch the contact surface and even damage the machine. The rosin press is used to extract plant essences oil, in the other words, it only gets used to squeezing some of the fine material. now let us explain in detail why such improper use...
My Bottle Jack Rosin Press Does Not Hold Pressure, Why?There are many factors that may cause the jack to not hold pressure, much apprecaited if you could check it out by yourself: Symptom Possible Causes Corrective Action Jack will not lift load Release valve not tightly closed Overload condition Air pressure inadequate Ensure release valve tightly closed Remedy overload condition Ensure adequate air pressure Jack will lift, but not hold pressure Release valve not tightly closed Overload condition Hydraulic unit malfunction Ensure release valve tightly closed Remedy overload condition Jack will not lower after unloading Reservoir overfilled Ensure load is...
U.S. Shipping Address Only - Only for American address Canada Shipping Address Only - Only for Canadian address
Shipped from Amazon or our own warehouse.
No import duties required
Expedited Shipping from Amazon US warehouse
2 days handling time.
3-7 Business day delivered.
Tips:
China factory warehouse only fulfills orders from countries where we have not built a local warehouse yet or products are out of stock in local warehouse.
Please do not choose cross-country warehouse to fulfill your order.
We apologies that we are unable to ship your order from other warehouse. So please do not buy products which are not available in your local country warehouse.
Due to Covid-19, we have to stop shipping order from our Belgium warehouse for European orders.
Delivery Time:
Estimated delivery time will be provided to you once your order is placed. Delivery time starts from the date of shipping, rather than the date of order.
Unless there are exceptional circumstances, we make every effort to fulfill your order within [5-7] business days after the date of your order. Business day means Monday to Friday, except holidays.
Tips:
Delivery time may vary due to carrier shipping practices, the distance between your location and the warehouse, method of delivery, and the items ordered.
Products may also be shipped in separate packages.
Is Shipping Discreet?
A plain unmarked brown external paper carton with our UPC label.
Drop Us A Line
We’re happy to answer any questions you have or provide you with an estimate. Just send us a message in the form below with any questions you may have.
Thanks for contacting us. We'll get back to you as soon as possible.
Built well. Would be perfect if they included 2 plastic round disc's made of high density plastic to aid in cleanup after pressing like the rectangular ones included in the rectangular press. Should last a lifetime
im in love with this press only con on this press is the legs are a little small so when you go to apply pressure it wants to tip over so maybe make the legs bigger and the rubber grippers should come with it and it should come with the kit like the maggnets and suchs since we are paying 300$ plus
It came with everything I wanted and it’s doing it’s job without fail,I’m happy with the results and will be keeping my eye on new products in the future.10 out of 10 would recommend a friend.
Really enjoy this unit had a smaller off brand one that bent but this one has a nice thick frame heavy duty gave her max pressure and she stayed perfectly straight love it